Manufacturer: Oneac
Type: ONEAC Power Conditioner

ONEAC CSR Series 9.6 KVA - Single Phase

CSR Series is a 9.6KVA, Single Phase, High Perfromance Power Conditioner

  • Frequency: 50/60 Hz
  • Load Regulation: +/- 2%
  • Load Regulation Response time: < 2 ms for a 50% change in load
  • Surge Voltage Withstand Capability: ANSI/IEEE C62.41 Category A&B 6kV/200 & 500 Amp, 100kHz ringwave, 6kV/3000A impulse waveform
  • Surge and Noise Rejection-Isolation: With unit under power, and ANSI/IEEE C62.41 Category A pulse applied, either normal mode (L-N) or common mode (N-G) at the input, the noise output voltave will be less than 10v normal mode and less than 0.5v common mode in all four quadrants.
  • Overload Capability: All units typically tolerate 10 times rated output for 0.5 cycle, 5.5 times rated output for 1 second and 3.5 times rated output for 5 seconds without degradation.

OPTIONS

Choose the options that meet your application needs:
 
Input Voltage Rating:
Adaptable voltage spreads allows options for voltage range.
Option
Rating
1
100 - 120 V (CSR06I only)
2
200 - 240 V
4
400 - 480 V (CSR07I and CSR10I only)
Example: For 240 V in, specify CSR10I-2XXXXX
 
 
Output Voltage Rating:
1
120 V 3 - 120/240 V Split Phase
2
240 V
Example: For 120/240 V Split Phase output, specify CSR10I-X3XXXX
 
 
Tap Setting:
Indicates which tap is configured at the factory - match to input breaker option.
Option
Rating
 
Option
Rating
A
200 V
H*
440 V
B
208 V
J*
460 V
C
220 V
K*
480 V
D
230 V
W**
100 V
E
240 V
Y**
108 V
F*
400 V
Z**
120 V
G*
415 V
 
 
* CSR07I and CSR10I only                            **CSR06I only
Example: For 200 V input tap, specify CSR10I-XXAXXX
 
Emergency Mains Off:
Allows the ONEAC power conditioner to interrupt power to the transformer utilizing input circuit breaker Accessories.
Option
Rating
X
no mains off
F
fail-safe EMO, SEMI-S2 compliant
K
fail-safe EMO, SEMI-S2 and SEMI-F47 compliant, auxiliary low voltage control output
T
fail-safe EMO, SEMI-S2 compliant, auxiliary low-voltage control output
Example: For fail-safe EMO, SEMI-S2 compliant, specify CSR10I-XXXFXX
 
 
 
 
Output Distribution & Convenience Circuits:
Various protected convenience receptacle options allow access to power.
Option
Rating
0
no convenience outlets
1
standard configuration (1) three gang IEC 320
2
(1) twist lock receptacle, (2) NEMA duplex receptacles
3 - 9
Alternate configurations of IEC 320, IEC 309, or NEMA twist (Call Powercom for options.)
 
            Example: For standard configuration, specify CSR10I-XXXX1X
 
 
 
 
Performance Characteristics:
CSR power conditioners may be specified with LED indicator panels or other special request features.
Option
Rating
0
no LED indicators or special option
1
standard LED indicators, input and output power applied
            Example: For standard LED indicators, specify CSR10I-XXXXX1
 
 
 

 

 
Additional Performance Characteristics:
Option
Rating
 
Frequency:
 
 
50/60Hz
Load Regulation:
±2%
 
Load Regulation Response Time:
< 2 msec for a 50% change in load
 
Surge Voltage Withstand Capability:
ANSI/IEEE C62.41 Category A&B, 6 kV/200 & 500 Amp, 100 kHz ringwave, 6 kV/3000 A, impulse waveform
Surge and Noise Rejection-Isolation:
With unit under power, and ANSI/IEEE C62.41
Category A pulse applied either normal mode (L-N) or common mode (N-G) at the input, the noise output voltage will be less than 10V normal mode and less than 0.5V common mode in all four quadrants using a Keytek 711A/J (or equivalent) surge generator and a low-voltage, high sensitivity probe.
 
Overload Capability:
All units will typically tolerate 10 times rated output for 0.5 cycle, 5.5 times rated output for 1 second, and 3.5 times rated output for 5 seconds without degradation.
 
 
Cooling:
 
 
convection

FEATURES & BENEFITS

Semiconductor-based systems need clean power
Computers, medical instrumentation, telecommunications and
manufacturing systems all rely on semiconductors. Semiconductors
perform by processing electric signals of less than a few
volts each and transient voltage disturbances can confuse that
process. Data may be lost or corrupted. Instructions garbled.
Processes stop. Systems need to be reset. Worse,
electrical overstress can destroy or degrade semiconductor material.
The results are increasingly unreliable operation or seemingly
random, sudden failures.

ONEAC’s unique solution
ONEAC power conditioners assure reliable electronic
performance by isolating semiconductors from the outside
electrical worlds they connect to. They differ from surge
suppressors in that they limit not only unit peak voltage
(amplitude), but also edge-speed (frequency) of electrical
transients. ONEAC’s low impedance transformer and Virtual
Kelvin Ground® remove the full spectrum of conducted power
line noise in all modes. More, they convert a noisy safety ground
to a noise-free signal ground. It’s an approach that has proven
uniquely effective against all conducted electrical disturbances.

For increased productivity
By any technical measure — surge voltage let-through,
frequency control, stability, predictability, load responsiveness,
durability, reliability — ONEAC power conditioners meet a far
higher performance standard than conventional protection
products. That translates into more reliable performance from
the systems they protect. Field tests confirm it. Those who use
ONEAC power conditioners in place of surge suppressor-based
products, with or in place of a dedicated IG circuit, dramatically
reduce system crashes, unexplained system errors and other
“soft” failures as well as hardware failures. So they enjoy
increased uptime and fewer service calls.

Robust design, proven durability
Designed and manufactured under ISO 9001 quality procedures,
ONEAC power conditioners have no parts that wear out. They
last far longer than surge suppressors. And are highly
reliable, even in harsh electrical environments. Their exceptionally
high mean time between failures (MTBF) backs that up. So do
we with a complete 5-year warranty. Plus our willingness and
ability to engineer site-specific protection schemes that eliminate
your power problems entirely.

TECHNICAL SPECIFICATIONS

See Brochure in "PDF DOWNLOADS"

APPLICATIONS

Universal

Not Rated for Medical Use

Request A Quote

Please feel free to request a quote by
telephone or use the form to email
your request.

Phone 1-800-288-9807
E-Mail info@powercom.com

Your Name
Phone
Your Email
Confirm Email
Product(s) Interested In
Loading Dock Yes No

Ship To Zip Code

Toshiba

Oneac

Eaton

Xtreme Power Conversion

Zonit

General Electric

Staco

MaxPower

SolaHD

Power Conditioners

Batteries

Line Protectors

UPS

Accessories